A chipped edge on a marble threshold or a cracked granite countertop is an expensive mistake, and it almost always comes down to the wrong blade or the wrong technique. Cutting stone and tile cleanly is a skill, but it is a learnable one. With the right marble cutting blade, a steady hand and a few habits, you can get factory-clean edges on marble, granite, vitrified tile and ceramic.

This guide is written for stone masons, tile fitters and serious homeowners across Panchkula and the Tricity. It covers which blade to use, wet versus dry cutting, and a clean step-by-step method. For the machines behind the work, see our main guide on angle grinders in Panchkula, and for whole-stone care, our detailed post on AKEMI stone and marble products.

The right blade is 90% of a clean cut

Stone and tile are cut with diamond blades, which work by abrasion rather than teeth. The rim design decides how clean the cut is, so this is the first choice to get right.

  • Continuous rim blade: a smooth, unbroken diamond edge. It cuts slower but gives the cleanest, chip-free finish. This is the blade for marble, polished granite, ceramic and vitrified tile where the edge shows.
  • Turbo rim blade: a continuous rim with a serrated edge. It cuts faster than a plain continuous rim while still leaving a fairly clean edge. A good all-rounder for granite and harder stone.
  • Segmented blade: visible gaps between segments. It cuts fastest and coolest but chips tile and polished stone, so keep it for concrete, brick and rough masonry, not finished surfaces.

In short: for a clean visible edge on marble or tile, reach for a continuous rim; for faster cuts in granite, a turbo. We stock marble cutting blades from Bosch (including zero-chipping types), Cameron, Alex, Awant, Axtrim, Cumi and more, in 4-inch and 5-inch sizes.

Marble cutter or angle grinder?

You can cut stone with a standard angle grinder and a diamond blade, but a dedicated marble cutter makes clean work much easier. A marble cutter is a compact machine with a flat base plate and a depth guide, so the blade runs at a set depth and the base keeps the cut straight and square. Many also take a water line for wet cutting.

KTC stocks dedicated marble and tile cutters including the Bosch GDC 120, GDC 121, GDC 125, GDC 140 and GDC 141, plus Accurate, Cameron and other value options. For repeat tile and marble work, a marble cutter pays for itself in cleaner edges and less waste.

Wet cutting vs dry cutting

How you manage dust and heat matters as much as the blade.

Wet cutting

  • Water cools the blade, so it lasts longer and the stone is less likely to crack from heat.
  • It suppresses dust almost completely, which protects your lungs.
  • It gives the cleanest edge, ideal for marble and polished granite.

Dry cutting

  • Faster to set up and better where water is a problem (near power, indoors on finished floors).
  • Produces fine stone dust that contains silica, which is a serious health hazard. Always wear a proper dust mask (a rated respirator, not a cloth) and cut in ventilated space.
  • Use short passes and let the blade cool to avoid overheating and glazing.

Whenever practical, cut wet. When you must cut dry, protect your lungs first.

Step by step: a clean cut in marble or tile

  1. Mark and support: mark your line clearly. Support the whole piece on a flat surface so both sides of the cut are backed. An unsupported edge snaps and chips.
  2. Tape the line: run masking tape along the cut line on the finished face. Tape holds the surface together and reduces chipping. Mark on the tape.
  3. Fit the right blade: continuous rim for a clean edge, turbo for faster granite cuts. Check the blade is rated above your machine’s speed and the arrows match the rotation.
  4. Set a shallow first pass: do not try to cut through in one go. Score a shallow groove first to guide the blade, then deepen it in passes. This prevents wandering and chipping.
  5. Let the blade do the work: feed steadily, do not force. Forcing overheats the blade, chips the edge and risks kickback.
  6. Finish from the back if the edge shows: for the most visible edges, score the face lightly, then complete the cut from the back so any minor chipping stays hidden.
  7. Dress the edge: ease the sharp edge with a diamond hand pad or polishing pad for a finished look.

Cutting holes for taps, fittings and pipes

For round holes in marble, granite or tile (basin taps, pipe outlets, fittings), use a diamond core bit rather than a blade. Run the core bit at a slight angle to start the ring, then bring it upright, and keep it cool with water. We stock marble core bits from 6 mm up to 67 mm and larger from Sanwa, XPT and others. There is more on core bits and hole saws in our guide to diamond blades, hole saws and core bits.

Common mistakes that chip stone

  • Using a segmented blade on tile: fast but it chips finished edges. Use continuous rim for anything that shows.
  • Cutting unsupported: the piece flexes and snaps. Back the whole cut.
  • Forcing the blade: heat cracks stone and glazes the diamond. Feed gently.
  • Skipping the tape: a small habit that saves a lot of chipping on polished faces.
  • No dust protection when dry cutting: stone dust is a genuine lung hazard. Mask up.

Good cutting habits pair with good machine habits. Read our angle grinder safety guide for guards, PPE and kickback control.

Frequently asked questions

Which blade cuts marble without chipping?

A continuous rim diamond blade gives the cleanest, chip-free edge on marble and polished stone. A turbo rim is a faster option for granite where a little more speed helps.

Can I cut granite with a normal angle grinder?

Yes, with a suitable diamond blade (turbo or continuous rim). A dedicated marble cutter with a base and depth guide makes it cleaner and easier, especially for straight edges.

Should I cut tile wet or dry?

Wet is cleaner, cooler and far safer for your lungs, so cut wet whenever you can. If you must cut dry, wear a rated dust mask and work in a ventilated area.

How do I stop tiles cracking when I cut them?

Support the whole tile, tape the cut line, score a shallow groove first, then deepen in steady passes without forcing the blade.

What do I use to cut a round hole in granite?

A diamond core bit of the right diameter, started at an angle and kept cool with water. KTC stocks marble core bits from 6 mm upward.

Blades, cutters and core bits at KTC Tools, Panchkula

From continuous rim marble blades to dedicated Bosch GDC marble cutters and diamond core bits, Khandelwal Trading Co. carries the stone-cutting range that tile fitters and stone masons across the Tricity rely on. Not sure which blade suits your stone? Bring a sample or send a photo on WhatsApp.

  • Call: 94175 65977
  • WhatsApp: wa.me/919417565977
  • Visit: Shop No. 4, Street No. 2, Maheshpur, Sector 21, Budanpur, Panchkula, Haryana 134117
  • Trade enquiries: get a quote